5-year construction warranty with Ponto Services!
Driven piles and foundation piles: what types are there?
Published: 29 October 2026.
How does the foundation carry the additional weight of an extension or roof addition? Bearing capacity is also important when repairing foundations. Sometimes a piled foundation is needed. Foundation piles include more than driven piles: screwed, bored and pressed systems are also available. Which types are there, and why does the choice vary between projects?
Why are foundation piles used?
A foundation pile transfers loads from the building to deeper soil layers and, depending on the design, can also resist forces that do not act straight downwards. A piled foundation may be needed when the soil near the surface does not provide sufficient bearing capacity, or when loads and deformation cannot otherwise be adequately controlled. The pile works together with ground beams or other structural elements; choosing a pile type alone therefore does not constitute a complete foundation design.
How many types of driven piles are there?
There is no fixed number of types. Piles can be classified by material (for example timber, precast concrete, steel or cast-in-place concrete) and by installation method (driving, screwing, boring, vibrating or jacking). Each group contains further variations. Not all foundation piles are therefore literally driven piles.
Four commonly discussed groups
- Precast concrete piles: the manufacturer makes these concrete piles in advance. Installers often drive them into the ground. They suit a range of loads, but driving can cause noise and vibration.
- Steel tubular piles: depending on the system, installers drive, screw or press steel tubes into the ground. Some variants also serve foundation repair work and sites with difficult access.
- Screw-displacement cast-in-place piles: the installer screws a steel tool into the ground. Concrete or grout then forms the pile in place. The specific system determines ground displacement and effects on the surroundings.
- Bored or continuous flight auger piles: a drill removes soil. Concrete or grout then forms the pile. This differs fundamentally from driving a precast pile into the ground.
Timber piles are mainly relevant to older existing foundations. Foundation repair therefore requires a separate assessment of their condition. The suitable pile type follows from the location and calculations, rather than a general ranking of the “best” piles.
What determines the choice of piling system?
The structural engineer and foundation specialist first assess the building loads, ground conditions, soil investigation results and existing foundations. They also consider access, space for equipment and effects on neighbouring buildings. Noise, vibration, ground displacement, groundwater and the work sequence can also play a part. A method may suit a new build on an open site. However, an extension between existing homes may need a different approach.
Reliable information is needed for the design. A cone penetration test provides information about soil resistance at different depths. Additional foundation investigations or information about the existing building may also be needed. Using these findings, the structural engineer determines the loads, the number and positions of the piles, and how they connect to the rest of the foundation.
Why do the surroundings matter?
Installing piles can affect the soil and nearby buildings. The effects vary by piling system and installation method. Where work poses a risk to neighbouring properties, a pre-construction condition survey or baseline survey can be useful, potentially supported by monitoring. This records the existing condition and makes it possible to track what happens during construction. Risks must be assessed at the design and construction planning stages; a baseline survey does not itself prevent damage.
What should you ask before work starts?
- Is the existing foundation documented, and are recent cone penetration test results available?
- What additional loads will the extension or roof addition create?
- Why is this piling system suitable for both the soil and the surrounding area?
- What noise, vibration or ground movement could occur?
- Are protective measures for neighbouring properties and a pre-construction condition survey needed?
- How will the connection between the new and existing foundations be designed?
Include foundations in your renovation plan
For a larger extension or roof addition, the design, structural engineering and construction must work together. Discuss the foundations early, before the layout and schedule are finalised. Read about when you need a structural engineer for a renovation and explore our pages on an extension and roof addition. Would you like to discuss your project? Get in touch.
Sources consulted on 29 October 2026: CROW Foundation Handbook: piled foundations; CROW on risk assessment and pre-construction condition surveys. The appropriate system and the investigations required depend on the project.